Design of a simple detection cell with extended optical path length for capillary electrophoresis: Application to multiresidue pesticide analysis

Absorbance detection in capillary electrophoresis (CE), offers an excellent mass sensitivity, but poor concentration detection limits owing to very small injection volumes (normally I to 10 nL). This aspect can be a limiting factor in the applicability of CE/UV to detect species at trace levels, particularly pesticide residues. In the present work, the optical path length of an on-column detection cell was increased through a proper connection of the column (75 mu m i.d.) to a capillary detection cell of 180 mu m optical path length in order to improve detectability. It is shown that the cell with an extended optical path length results in a significant gain in terms of signal to noise ratio. The effect of the increase in the optical path length has been evaluated for six pesticides, namely, carbendazim, thiabendazole, imazalil, procymidone triadimefon, and prochloraz. The resulting optical enhancement of the detection cell provided detection limits of ca. 0.3 mu g/mL for the studied compounds, thus enabling the residue analysis by CE/UV.

Alternative methodologies for the determination of aldehydes by capillary electrophoresis

This paper describes 2 alternative methodologies for the determination of selected aldehydes (formaldehyde, acetaldehyde, propionaldehyde, acrolein, and benzaldehyde) by capillary electrophoresis (CE), the first approach is based on the formation of aldehyde-bisulfite adducts and employs free solution CE with reversed electroosmotic flow and indirect detection, using 10 mmol/L 3,5-dinitrobenzoic acid (pH 4.5) containing 0.2 mmol/L cetyltrimethylammonium bromide as the electrolyte. This novel methodology showed a fairly good sensitivity to concentration, with detection limits with respect to a single aldehyde on the order of 10-40 mu g/L, a reasonable analysis time (separation was achieved in <8 min), and no need for sample manipulation. A second approach was proposed in which 2,4-dinitrophenylhydrazine derivatives of the aldehydes were detected in a micellar electrolyte medium (20 mmol/L berate buffer containing 50 mmol/L sodium dodecyl sulfate and 15 mmol/L beta-cyclodextrin). This latter methodology included a laborious sample preconcentration step and showed much poorer sensitivity (0.5-2 mg/L detection limit, with respect to a single aldehyde), despite the use of sodium chloride to promote sample stacking. Both methodologies proved adequate to evaluate aldehyde levels in vehicular emissions. Samples from the tailpipe exhaust of a passenger car vehicle without a catalytic converter and operated with an ethanol-based fuel were collected and analyzed; the results showed high levels of formaldehyde and acetaldehyde (0.41-6.1 ppm, v/v). The concentrations estimated by the 2 methodologies, which were not in good agreement, suggest the possibility of striking differences in sample collection efficiency, which was not the concern of this work.

Determination of 2-methylimidazole and 4-methylimidazole in caramel colors by capillary electrophoresis

The use of chemical preservative compounds is common in the food products industry. Caramel color is the most usual additive used in beverages, desserts, and breads worldwide. During its fabrication process, 2- and 4-methylimidazole (MeI), highly carcinogenic compounds, are generated. In these cases, the development of reliable analytical methods for the monitoring of undesirable compounds is necessary. The primary procedure for the analysis of 2- and 4-MeI is using LC- or GC-MS techniques. These procedures are time-consuming and require large amounts of organic solvents and several pretreatment steps. This prevents the routine use of this procedure. This paper describes a rapid, efficient, and simple method using capillary electrophoresis (CE) for the separation and determination of 2- and 4-MeI in caramel colors. The analyses were performed using a 75 μm i.d. uncoated fused-silica capillary with an effective length of 40 cm and a running electrolyte consisting of 160 mmol L-1 phosphate plus 30% acetonitrile. The pH was adjusted to 2.5 with triethylamine. The analytes were separated within 6 min at a voltage of 20 kV. Method validation revealed good repeatability of both migration time (<0.8% RSD) and peak area (<2% RSD). Analytical curves for 2- and 4-MeI were linear in the 0.4-40 mg L-1 concentration interval. Detection limits were 0.16 mg L-1 for 4-MeI and 0.22 mg L-1 for 2-MeI. The extraction recoveries were satisfactory. The developed method showed many advantages when compared to the previously used method. © 2013 American Chemical Society.

Validation of a stability indicating capillary electrophoresis method for the determination of darunavir in tablets and comparison with the of infrared absorption spectroscopic method

Darunavir (DRV) is a protease inhibitor used in the treatment of HIV infection, which constitutes a keystone in the therapy of patients infected with this virus. There is no monograph described in official compendia. The literature provides few methods of analysis for the determination of DRV in pharmaceuticals which include TLC, IR, UPLC, HPLC, HPLC-MS, HPLC-MS/MS, but there are no reports of the use of capillary electrophoresis (CE) for the determination of this drug. Thus, this research proposed the development and validation of a CE method for the determination of DRV in tablets. The method was completely validated according to the International Conference on Harmonization guidelines, showing linearity, selectivity, precision, accuracy and robustness. The migration was achieved in less than 1 minute using fused-silica uncoated capillary with an id of 50 μm and total length of 21 cm and voltage of +20 kV. The sample injection was performed in the hydrodynamic mode. The method was linear over the concentration range of 50-200 μg mL-1 with correlation coefficient 0.9998 and limits of detection and quantification of 7.29 and 22.09 μg mL-1, respectively. The drug was subjected to acid, base, oxidation and photolysis degradation. Degradation products were found interfering with the assay of DRV, therefore the method can be regarded as stability indicating. The validated method is useful and appropriate for the routine quality control of DRV in tablets.

Indirect determination of chloride and sulfate ions in alcohol fuel by capillary electrophoresis

A capillary zone electrophoresis method using indirect UV detection for the analysis of chloride and sulfate in alcohol fuel samples was developed. The anions were analyzed in less than 3 min using an electrolyte containing 10 mmol 1(-1) chromate and 0.75 mmol 1(-1) hexamethonium bromide (HMB) as electroosmotic flow modifier. Coefficients of variation were better than 0.6% for migration time (n = 10) and between 2.05 and 2.82% for peak area repeatabilities. Analytical curves of peak area versus concentration in the range of 0.065-0.65 mg kg(-1) for chloride and 0.25-4.0 mg kg(-1) for sulfate were linear with coefficients of correlation higher than 0.9996. The limits of detection for sulfate and chloride were 0.033 and 0.041 mg kg(-1), respectively. Recovery values ranged from 85 to 103%. The method was successfully applied for the quantification of sulfate and chloride in five alcohol fuel samples. The concentration of sulfate varied from 0.45 to 3.12 mg kg(-1). Chloride concentrations were below the method's LOD.

Comparative study over methods developed for quantification of darunavir in tablets by environmental friendly infrared and capillary electrophoretic techniques

Darunavir, a protease inhibitor used in the treatment of HIV infection, presents few methods for its determination in pharmaceuticals. Infrared (IR) spectroscopy offers the possibility of obtaining spectra relatively quickly, providing interesting information, analytically, qualitatively or quantitatively. Capillary electrophoresis (CE) performs separations of high efficiency in shorter time with reagents and samples in small quantity. These two methods are cost-benefitted when we evaluate the green level and the cost of analysis. Faster and cheaper methods without generating organic waste by IR and CE for the quantification of darunavir were developed and validated, focusing socioeconomic impact of analytical decisions. If the cost of acquisition, maintenance, production, analysis and conditioning of drugs and pharmaceuticals is high, consequently the price of this product in the market will be higher and it cannot be accessible to the patient. Treatment failure not only affects the quality of life of patients, but also contributes significantly to the economic burden of the health system. In this context there is a tool called Analysis of the Life Cycle, which comes to make us think in a multidimensional way focusing the whole, the parts and especially the interaction among the parts of a system.

Methacycline: A Review of Analytical Methods

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Desenvolvimento e validação de método analítico para determinação de benzoato, sorbato, metil e propilparabenos em produtos alimentícios utilizando a eletroforese capilar

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Desenvolvimento de método para determinação de composição de atmosfera modificada pela presença de inibidores de corrosão

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Development of a method for sampling and determination of corrosion inhibitors in modified atmospheres

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise quimico-farmacêutica de Darunavir etanolato em comprimidos e de seu complexo de inclusão

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determination of sildenafil and vardenafil by capillary zone electrophoresis using capacitively coupled contactless conductivity detection

A method based on capillary electrophoresis with capacitively coupled contactless conductivity detection (CE-C4D) for determination of two important phosphodiesterase type-5 inhibitors (sildenafil and vardenafil) is introduced. The background electrolyte (BGE) consisted of an aqueous solution of 500 mmol L-1 acetic acid, and the capillary was previously treated with polybrene solution to prevent cationic analytes from adsorbing onto the inner surface. Although the analytes migrate in the counter flow, the total time is short. An instrument with two C4D detectors allowed a seamless transition from a fast method (less than one minute) but of low-efficiency using the first detector to a more efficient method using the second detector. The analysis of commercial tablets showed no significant difference between CE-C4D and HPLC methods. Conductivity detection is a well-known low selectivity detection scheme, which in conjunction with the high mobility of the co-ion in the BGE (hydroxonium) allows one to predict that other cationic analogues of sildenafil can also be detected. This is an interesting feature given the increasing number of compounds in this class. © 2013 The Royal Society of Chemistry.

Determination of fluoroacetate and fluoride in blood serum by capillary zone electrophoresis using capacitively coupled contactless conductivity detection

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Analytical Methods for the Determination of Chlorhexidine: A Review

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

PCR Multiplex fluorescente para detecção de bactérias em sêmen bovino

Este estudo teve como objetivo avaliar o limiar de detecção da técnica de PCR multiplex fluorescente aliada a eletroforese capilar na detecção de agentes infecciosos em amostras de sêmen experimentalmente contaminadas com concentrações decrescentes das bactérias Brucella abortus, Leptospira interrogans sorovar pomona, Campylobacter fetus e Haemophilus somnus. Amostras de sêmen bovino foram experimentalmente contaminadas com concentrações decrescentes de bactérias obtidas através de diluições seriadas na base 10 de modo a obter-se amostras contendo desde 1 vez até 10-7 bactérias/mL a partir da concentração inicial de Leptospira pomona, Brucella abortus, Campylobacter fetus e Haemophilus somnus. As diluições foram efetuadas individualmente para cada bactéria, bem como nas diferentes concentrações necessárias para a padronização do teste de multiplex PCR. As extrações de DNA de todas as soluções contendo espermatozóides e bactérias analisadas no presente estudo foram realizadas segundo protocolo descrito por Heinemann et al. (2000). Os produtos de PCR multiplex foram avaliados por eletroforese em gel de poliacrilamida 8% e separação eletroforética por sistema capilar em equipamento automático de análise de fragmentos de DNA MegaBace. Observou-se a amplificação de fragmentos de 193pb, 330pb, 400pb e 415pb a partir do DNA de B. abortus, L. pomona, H. somnus, C. fetus, respectivamente. Na análise por eletroforese capilar de produtos da PCR multiplex do DNA para detecção simultânea dos quatro patógenos observou-se a sinal de positividade até a diluição de 10-3 bactérias/mL vezes da concentração inicial da solução estoque de cada bactéria. A técnica de PCR multiplex aliada à eletroforese capilar foi usada pela primeira vez para o diagnóstico direto de quatro bactérias patogênicas no sêmen, demonstrando ser um método rápido na detecção de bactérias causadoras de doenças reprodutivas.